Forged Valve Body Manufacturing: 7 Controls Buyers Should Verify
سپتامبر 2, 2026

Bonnet Gasket Replacement for Forged Valves

اکتبر 17, 2026

QUICK ENGINEERING ANSWER

Order a replacement bonnet gasket against the valve identification and an approved part drawing, not nominal size and pressure Class alone. Confirm the gasket construction, sealing-element dimensions, thickness, winding metal, filler and any separate rings. A description such as SS316 plus graphite identifies gasket constituents; it does not identify the valve body or trim. This guide covers specification review, not an interchangeable-parts catalogue or an assembly procedure.

Two CLDG drawing examples: dimensions and tolerances

Two joint-gasket detail drawings from CLDG show why a replacement request needs more than three nominal dimensions. Both specify a thickness of 3.5 mm, but the diameter allowances differ. The table reproduces the diameter callouts, with A and B identifying the two examples.

These examples explain how to read a drawing. For an actual replacement, confirm the applicable valve drawing, gasket construction and material specification. Dimensions alone do not establish NPS/Class compatibility or a pressure–temperature rating.

Two CLDG joint-gasket drawings: nominal sizes and explicit tolerances (mm)
Drawing sampleID with explicit deviationsOD with explicit deviationsMarked thicknessDerived ID / OD intervals
الف35 (+0.2 / +0.1)45 (0 / −0.1)3.5ID 35.1–35.2 / OD 44.9–45.0
ب52 (+0.1 / 0)64 (−0.1 / −0.2)3.5ID 52.0–52.1 / OD 63.8–63.9

For A, “35 × 45 × 3.5” leaves out the positive ID allowance: an ID of exactly 35.0 mm falls below the marked 35.1 mm minimum. For B, an OD of exactly 64.0 mm exceeds the marked 63.9 mm maximum. Both parts could be described using the correct nominal dimensions and still miss the drawing requirement. Send the applicable drawing and its tolerances with the replacement request. Confirm thickness tolerance separately; the table reports only the marked thickness.

Why are NPS and Class not enough?

“A gasket for a Class 800 forged valve” is a starting point, not a complete spare-parts specification. The body–bonnet joint belongs to a particular valve design. Confirm the manufacturer, model, nominal size, pressure designation and part or assembly drawing revision before comparing a proposed replacement.

First identify whether the joint uses a spiral-wound gasket, another bolted-joint sealing form, or a pressure-seal arrangement. A similar-looking ring is not evidence of interchangeability. Our bolted-bonnet and pressure-seal comparison explains the different load paths; the task here is to specify the correct replacement for an existing joint.

Read the material description component by component

CLDG’s specification records distinguish gasket material from the body, trim and packing. Keep that separation in a purchase specification. In a spiral-wound gasket, the metal winding and the filler are distinct constituents. Inner and outer rings, where present, need their own material identification.

CLDG specification check: what each material field actually describes
Specification fieldIllustrative entryWhat must remain separate
Body / bonnetASTM A182 F304, when specifiedNot changed by SS316 appearing in a gasket line
Seat / closure-member surfacesApproved base material and hardfacingNot inferred from the gasket winding
Gasket windingSS316, if explicitly specifiedMetal strip, not the complete valve material grade
Gasket fillerGraphite or PTFE, as specifiedFiller identity is not the winding-metal identity
Inner / outer ringsState presence and each materialDo not assume the rings match the winding metal
بسته بندی ساقهSeparate packing specificationNot established by a bonnet-gasket description

Scope: this table shows specification roles, not standard fitted materials, stock availability or a service-compatibility guarantee. SS316 and SS316L are not silently substituted for one another. Review the stated grade, filler product and actual medium, temperature and pressure.

Measure the sealing element, not just the largest ring

CLDG’s engineering dimension checks treat gasket inside diameter, outside diameter and construction as separate inputs. For a ring-equipped spiral-wound gasket, distinguish the wound sealing element from the inner and outer rings. Record which feature each diameter belongs to. Include thickness in its specified, uncompressed condition and the drawing tolerances.

Replacement-gasket dimension and identity checklist
Item to confirmUnit / identifierRequired reference
Sealing-element ID and ODmm; identify the measured featureApproved gasket drawing and mating joint
Uncompressed thicknessmm, including toleranceSpecified construction / part drawing
Separate-ring dimensionsmm and presence / absenceInner and outer rings identified separately
Profile and locating featuresDrawing-defined shape and dimensionsJoint recess, seating surfaces and gasket drawing
Part identityManufacturer, part number and revisionValve identification and approved records

An old compressed or damaged gasket can help identify the part, but it is not a reliable substitute for the specified new-part dimensions. Photographs help locate the joint; they do not establish hidden dimensions or a material grade.

Does ASME B16.20 define the bonnet gasket?

ASME B16.20–2023 addresses metallic gaskets for pipe flanges and identifies referenced flange standards. Its published scope does not provide a universal spare-part lookup for every valve body–bonnet joint. A bonnet gasket can use a recognized gasket construction while still requiring design-specific dimensions. Apply the specified standard where it is actually applicable, then confirm the manufacturer’s drawing and part reference.

Do not use the pipe-end flange size as the bonnet-gasket dimensions. Likewise, a higher-alloy winding is not automatic proof that a different filler or joint geometry is suitable. Service compatibility, seating condition and the approved assembly requirements remain separate checks.

What should a useful replacement request include?

Start with the valve identification and clear photographs, then add the part drawing or spare-parts reference if available. State the joint type, sealing-element ID/OD/thickness, ring configuration, winding metal and filler separately. Include the actual medium and operating pressure/temperature, plus any specified cleaning, testing or documentation requirements. Missing dimensions should remain open for confirmation rather than being guessed from a similar valve.

For a new valve rather than a spare gasket, use our forged gate valve product page. For order-specific inspection and release documents, refer to the valve inspection and test plan guide. Replacement approval and maintenance must follow the actual valve manufacturer’s authorized documentation; this page supplies neither a universal torque value nor a live-maintenance procedure.

Three questions that change the purchase decision

Does SS316/graphite mean the valve has F316 trim?

No. When that entry identifies the gasket, it describes its constituents. Body, trim, stem and packing need their own specified material identities.

Can I buy a replacement from NPS and Class alone?

Not reliably. Confirm the manufacturer’s part identity, joint construction and specified dimensions. Matching nominal valve data does not establish gasket interchangeability.

Is pure graphite interchangeable with SS316/graphite spiral wound?

No automatic substitution is justified. They are different constructions. Verify the approved gasket product, geometry, service limits and joint requirements before proposing a change.

Standards and data basis

The dimension examples are drawn from two CLDG joint-gasket detail drawings. Diameter intervals are calculated from the explicitly marked deviations. The product photograph is from CLDG’s image library. Use the applicable order-specific drawing and material specification for procurement and maintenance.

fa_IRPersian