The main difference between a T-type and a Y-type globe valve is the arrangement of the seat and flow passage. A Y-pattern can provide a less restrictive flow path, but body shape alone does not establish control accuracy, allowable temperature or suitability for a particular duty. Compare the actual valve’s Cv, trim, opening range and pressure–temperature rating.

Что такое запорный клапан?
Шаровой клапан — это тип клапана, используемый для регулирования или остановки потока жидкости.
Свое название он получил из-за круглой формы тела.
Внутри клапана подвижная заглушка или диск давит на неподвижное седло, регулируя поток.
Благодаря своей точности управления шаровой клапан часто используется в трубопроводах, требующих точной регулировки расхода.
Типичные области применения включают паропроводы, системы водоснабжения и химические перерабатывающие заводы.
Понимание деталей шарового клапана
Стандартный шаровой клапан состоит из следующих частей:
- Тело: Основная внешняя оболочка, в которой находятся все остальные компоненты
- Капот: Верхняя крышка, которая закрывает шток и обеспечивает доступ для обслуживания.
- Корень: Шток, который перемещает диск вверх или вниз.
- Диск: часть, которая открывает или закрывает путь потока
- Сиденье: Поверхность, на которой диск уплотняется, чтобы остановить поток
- Маховик или привод: Используется для ручного или автоматического управления клапаном.
Эти детали шарового клапана работают вместе, обеспечивая герметичность и плавное регулирование потока.
T-type: check the required flow and throttling duty
A conventional T-pattern directs flow through the seat region in a less direct path. It may suit the required isolation or throttling duty, but the result depends on the selected trim and operating conditions. Do not select it solely on a general claim of “more precise control”.
Y-type: verify the benefit with model-specific data
A Y-pattern uses an inclined seat/stem arrangement to make the flow passage less restrictive. Where the selected model provides a higher Cv at the relevant opening, it can reduce the pressure drop for a given liquid flow. It does not automatically have a higher pressure or temperature rating, and it is not inherently less accurate at control.
Сравнение шаровых клапанов типа T и типа Y
| Selection question | T-type | Y-type |
|---|---|---|
| What is the flow path? | Conventional globe-seat routing | Inclined arrangement, potentially less restrictive |
| What pressure drop should I expect? | Calculate using the selected model’s Cv at the intended opening | Use its own Cv; do not apply a fixed reduction percentage |
| Which controls more accurately? | Verify trim characteristic, actuator and operating range | Verify the same factors; shape alone is insufficient |
| Which handles higher temperature? | Check material, rating, packing and service limits | Check the same limits; Y-shape is not a temperature rating |
| Can it fit the line? | Check face-to-face, stem travel and service clearance | Also check inclined bonnet/actuator clearance |
A liquid-flow comparison using Cv
For a simplified, non-choked turbulent liquid calculation in US units, ΔP = SG × (Q / Cv)², where Q is in US gpm and ΔP is in psi.
Illustrative values—not CLDG test results: at 40 US gpm and SG = 1, a candidate with Cv = 20 gives 4.00 psi; a candidate with Cv = 30 gives about 1.78 psi. This comparison shows why the actual coefficient matters. It does not assign either value to a T-type or Y-type valve and does not establish a universal saving.
Use the liquid Cv/Kv calculator for an initial estimate within its stated limits. Steam, gas, viscous flow, cavitation, flashing and choked-flow conditions require an appropriate sizing method. A shell or seat-leakage test result is not a tested Cv value.
Can a Y-type globe valve be installed in any direction?
No general permission can be inferred from the Y-pattern name. Follow the actual valve’s flow arrow, installation instructions and approved drawing. Confirm stem/actuator orientation, support and maintenance clearance for the selected model.
What should I send for selection?
Send the fluid, flow rate or operating range, upstream and downstream pressure, temperature, connection and size if known. State whether the duty is isolation, occasional throttling or continuous regulation. For welded connections, the pipe schedule and end-connection tool can help describe the pipe interface; it does not determine the valve’s Cv.
You can request a globe-valve selection review with incomplete information. Identify what is known and what still needs confirmation.





